Print Page | Close Window

ct meg header install

Printed From: Brock's Performance
Category: Technical Articles and Information
Forum Name: Product Discussions (Customers Welcome to add a Topic)
Forum Description: An area to discuss particular products, dyno results, our combinations etc. in detail.
URL: https://forums.brocksperformance.com/forum_posts.asp?TID=2497
Printed Date: November/11/2026 at 10:12am
Software Version: Web Wiz Forums 12.01 - http://www.webwizforums.com


Topic: ct meg header install
Posted By: toledoUPSguy
Subject: ct meg header install
Date Posted: March/08/2015 at 7:04pm
Need some help please.  Compared to all the other Brock's products I have or have had the instructions for the 2102+ zx14r seem a touch confusing.  There is nothing saying where the muffler mounting bracket goes.  That wasn't too bad, between looking for bolts that match up and a quick call to Lee Prichard to confirm had it done.  Instructions say to put a thing layer of permatex on the inside of each header tube but that won't do anything since the tube slides in the spigot so I hope I guessed right and put some inside each spigot.

Here is  my real question though do I use 4 or 8 springs on the header mounts?  Instructions say 1 spring each  but there is enough for 2 on each.   Is there a diagram showing which holes in the flange to which loop on the headers?

This is how I currently have it, was in a hurry since my son was getting impatient with me not paying undivided attention to him and I'm 99% I've got it wrong.


can't get the image to upload



Thanks in advance.



-------------
The man on top of the mountain didn't fall there.

2014 zx14r in nuclear sunset orange and black.



Replies:
Posted By: toledoUPSguy
Date Posted: March/08/2015 at 11:10pm
I went ahead and put 8 on.  Not sure if I've got the oriented correctly but they're on.

-------------
The man on top of the mountain didn't fall there.

2014 zx14r in nuclear sunset orange and black.


Posted By: toledoUPSguy
Date Posted: April/14/2015 at 5:41pm
Since there are no specific instructions for the CT Meg may I suggest you might want to put an addendum to the instructions for it.  Might want to put a note in about muffler mounting bracket and this.  I was double checking some items and noticed the muffler is hitting the original exhaust hanger bushing.  Might want to make a note that it needs to be removed, or did I do something wrong?

I'd post a picture but can't figure out how to here.



-------------
The man on top of the mountain didn't fall there.

2014 zx14r in nuclear sunset orange and black.


Posted By: *EJ*
Date Posted: April/15/2015 at 3:31pm
toledoUPSguy,

Thank you for bringing this to our attention, make sure bracket that mounts to foot peg is behind bracket welded on muffler, this will give more clearance between muffler and stock bushing mount.


Posted By: toledoUPSguy
Date Posted: April/15/2015 at 4:31pm
Thanks EJ, that is how I have it mounted.  I just removed the bushing so now it's even lighter.

-------------
The man on top of the mountain didn't fall there.

2014 zx14r in nuclear sunset orange and black.


Posted By: Darkarcher
Date Posted: April/05/2016 at 8:45am
I did the same thing. Since the CT pipes go inside the flange I just put the permatex on the outside. Makes no sense to put it on the inside. Also I only used 2 springs per pipe (cause thats all it comes with) but instead of putting them all on the bottom row I put one on top and one on bottom. It just made the most sense given the orientation of the attachment points.



Print Page | Close Window

Forum Software by Web Wiz Forums® version 12.01 - http://www.webwizforums.com
Copyright ©2001-2018 Web Wiz Ltd. - https://www.webwiz.net